Put simply, an atomising spray nozzle is a tool that generates a spray of liquid mist, essentially fragmenting liquid into very fine droplets.

Applications for atomising spray nozzles can range from dust suppression, cooling and humidification through to cleaning and disinfection. Depending on the application, users will require either a pneumatic (air assisted) or a hydraulic (liquid only) atomising spray nozzle.

A hydraulic atomising spray nozzle is capable of fragmenting liquid even at low pressures using only liquid. It relies on pressurised liquid being forced through a small passage to atomise and create the spray. It’s simple to set up and users only need a water supply for this to work, whereas pneumatic spray nozzles (also known as air atomising spray nozzles) use liquid as well as compressed air to assist in atomising the liquid. Pneumatic spray nozzles can provide finer atomisation and can spray a lower, more controlled volume of liquid. The set-up can be more complicated and more costly due to the need for a compressed air supply, which is something that needs to be considered.

Choosing the right atomiser can seem overwhelming, but here are five things to consider when making the decision. For the purpose of this article, we will focus on air assisted atomising nozzles.

It is important to note that pneumatic atomising nozzles mix air with liquid flow, breaking up the fluid into smaller droplet particles and there are two kinds of set-up:

With internal mixing, the increase in air-flow rate will cause a decrease in the flow rate of the liquid with finer drops and can produce fan or cone patterns. External mixing allows atomisation of viscous liquids or those which contain solids in suspension, but the external mix units can generate only a flat jet.

When choosing an atomising nozzle, users need to consider its intended application, supply pressure and position. There are many variables involved when deciding which spray nozzle will offer the right solution for each user application. Here are our five tips to help:

Is there a pressurised liquid source available or only a compressed air source available? If there is no pressurised liquid supply, users will need a gravity or siphon-fed (pneumatic) nozzle. There are some drawbacks to consider with this option. Siphon-fed nozzles are best suited for applications that require continuously spraying a low-viscosity liquid at a low volumes. It is also possible to use a pressure vessel for liquids in some applications.

Another factor when choosing between nozzles is the viscosity (thickness) of the liquid it will need to spray. Depending on the type of air atomising spray nozzle chosen, as mentioned above, users can complete the atomising process either inside the nozzle chamber (internal mixing) or outside the nozzle chamber (external mixing). External nozzles are more suited to thicker, more viscous liquids. Having said that, if the viscosity is normal, internal mixing will provide more spray options such as cone patterns.

If the application requires a set volume of liquid, users can choose the correct nozzle based on its flow rate. As a rule, external-mix nozzles inherently dispense more liquid than internal-mix nozzles, as they have fewer restrictions on the liquid flow. For applications requiring higher volumes, a liquid-only atomising nozzle will provide an increase in litres per hour. However, using liquid-only nozzles will increase the droplet size.

Finer droplets are crucial in many atomising nozzle applications. Benefits include even distribution and liquid conservation. Internal-mix nozzles excel at providing the smallest droplet size possible. External-mix and liquid-only nozzles produce larger droplet sizes, but do increase the volume sprayed, so knowing what is more important here is key.

The impact force is the force generated by the jet of water deflected by the impact surface and its strength is often expressed in kg/cm2 or lb/inch2. The type of nozzle being sprayed can influence impact. A solid stream nozzle and flat fan nozzle spraying from the same distance have the same pressure and flow rate. However, the solid stream nozzle provides more impact than the flat fan nozzle because the solid stream is concentrating more flow per area than the flat fan nozzle.

The wrong choice in spray nozzles can lead to ineffective spraying, liquid or product wastage and reduced performance. If in doubt, Tecpro experts can assist users with the right choice for their application.

The benefits of aseptic filling technology over traditional techniques are well-known in the food...

The University of Technology Sydney (UTS) and Young Henrys Brewery are pairing brewing technology...

Sarah Qian is a self-confessed foodie vegan whose graduation story is far from ordinary —...

Relying on a one-stop shop

The Importance of Using Industrial PCs & Monitors to Ensure Safety and Compliance in Food Processing

Cooling & temperature control applications with cryogenics

Leuze DRT25C — dynamic reference diffuse sensor

The optimum plant-based taste experience

Testing food textural properties with Lloyd TA1

MET0003C - X12 Global Teaser

Nutrition education on the menu for health professionals

New rapid water test could reduce gastro outbreaks

Plan to support digital capability in health workforce

Deakin University opens battery research and innovation hub

Federal government to boost funding for Factory of the Future

IICA Functional Safety Engineer training courses

Ultimaker and MakerBot announce completion of merger

Rockwell Automation announces FactoryTalk Design Hub

The ethical challenges of working with human blastoids

NHMRC announces $375m in Investigator Grants, gender equity scheme

Spray drying innovation is leading to significant efficiency gains

Schizophrenia may increase dementia risk

50% of coral reefs may face unsuitable conditions by 2035

Westwick-Farrow Media Locked Bag 2226 North Ryde BC NSW 1670 ABN: 22 152 305 336 www.wfmedia.com.au Email Us

Our food industry media channels - What’s New in Food Technology & Manufacturing magazine and the Food Processing website - provide busy food manufacturing, packaging and design professionals with an easy-to-use, readily available source of information that is crucial to gaining valuable industry insight. Members have access to thousands of informative items across a range of media channels.

Membership is FREE to qualified industry professionals across Australia.